溶解式低溫干燥機

◆服務的特點 Product features

※擁有安全共同的撒氣學習壓力和露點

1.降解塔之程度與長度經實驗報告最終精密五金測算，塔床障礙小， 保障了減少有機廢氣氣體常溫、干燥劑5秒的相處時光，提供樣品氣的露點規定。

2.30％的太干劑余下量，應用于賠償費太干劑的天然受損，抓實太干。

3.巨型散出器，事關環流豎直采用干燥處理劑層，消去溝流的情況。

※再造氣量損耗率大于14％

1.睿智的機筒制作，存為100％的吸咐形成，存貯的形成廣泛用于增多可二次利用環節的可二次利用氣氣溫，不斷提高系統的解吸性能，使人可二次利用更完全徹底。

2.烘干和粉碎利用返向形成對流計劃書，濕的空氣流下干的吸劑時限果較好。粉碎氣出口到含濕量控住在亞飽和情形，使消音器原理器及改裝排氣管路通道無結霜現象之慮。

3.可基于潮濕機的啟動負債需要量可以調節回收氣攝入量，保證回收暖濕氣流維持平穩，回收壓低至臨界狀態。

※烘干劑在使用平均期限長

1.恰當的機筒盡寸，使氣體在空氣晾干劑層的水流量和時間間隔保護好的睡眠狀態，多方面發揮出來空氣晾干劑的安全性能。

2.有效的軟件系統配值，在氣旋加入機筒前，經除油加工處理及時的清楚氣旋中內動植物油物與重環保問題物，解決皮膚干燥劑層受環保問題。

※設備通過了趣味性高的質量手動及液壓閥和安全可靠的全智能可代碼編程序的控制開關，電腦接口信賴，手動反復彰顯雙塔載荷，反復定期當場可編，出廠的調整10min。閥體蓄電量超過50萬次拉伸動作。

※壓力容器封頭內部作冷熱浸鋅防水正確處理，10年不浮銹。

※動作較準、特性動態平衡、方法簡單便捷，按裝不必基礎上。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆核心高技術參數表設置 Main technical parameters